Braeburn Thermostat Not Working? Do This!

0
Braeburn Thermostat Not Working

Despite switching on the Braeburn Thermostat the room is freezing cold and you find that you cannot turn up the heat.

What causes this?

Why is My Braeburn Thermostat Not Working?

Table of Contents

1. Your Braeburn thermostat wiring is wrong

Check thermostat wiring to make sure that the heating and cooling stages are connected to the correct terminals on the wiring terminal block.

This prevents the Braeburn 1010 Builder model thermostat from turning on heating instead of cooling, or cooling instead of heating.

Is your recently installed eco-friendly thermostat not able raise the heat thermostat above certain temperature?

2. Your Braeburn thermostat is dirty.

Dirt and dust accumulation on your thermostat and mechanical contacts can hinder with how it reads your settings.

To access the screen cleaning mode for the Braeburn 5310 and 5320 programmable touchscreen thermometers hold the CLEAN TouchPad™ for 3 seconds. The screen will show a countdown timer for 30 seconds. The screen is locked and you can continue cleaning it. After 30 seconds the display resumes to normal.

Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are the “touch sensitive” segments used to adjust your thermostat.

Fix – Take a spongy cloth and lightly rub away any visible dust or dirt residue.

On no occasion should you spray any liquid directly on the thermostat. Squirt your cleaning liquid on a soft cloth and then clean the screen with the moist cloth. Only use water or household glass cleaner on screen.

Fix – Use an electrical contact cleaner to remove corrosion mechanical contacts.

View on Amazon

3. The air flow to your thermostat is blocked

Check the vents and verify that they are open and that there are no objects such as furniture, pillars, fireplaces and so forth blocking the free movement of air from the thermostat to the room.

Ther could be a big difference in temperature if you have accidentally blocked off the heat vent or covered a radiator in your bedroom.

If you are installing the Braeburn 1010 Builder Series Non-Programmable Single Stage Heat/Cool thermostat, be sure to locate it four to five feet above the floor in line with relevant building codes.

Make sure to install the Braeburn 1010 thermostat in a location that provides good airflow and avoid areas behind doors, near corners, air vents, direct sunlight or near any heat generating device.

4. Your thermostat requires battery replacement

Braeburn systems recommends replacing the thermostat batteries annually or if the thermostat will be unattended for an extended period of time.

The Low Battery Indicator on the Non-Programmable Braeburn 3020 and 3022 Thermostats l indicates when the batteries need to be replaced.

You may have to remove it from its base that is stuck to the wall.to see the back. The body of the thermostat releases from the wall mount by hinging upward.

To remove Braeburn thermostat to change batteries:

  1. Grab a hold of the thermostat unit
  2. Pull the battery cover from the wall. The roller like hinges make detachment easy
  3. The battery compartment will be on the back
  4. Change batteries and repace with the recommended battery size and type

Most Braeburn thermostats require 24 Volt AC Power or two (2) properly installed “AA” Alkaline batteries for proper operation.

5. Your thermostat is due for its yearly calibration

Fix: Compare your thermostat readings with a functioning thermometer. Repeat this process after fifteen minutes, then thirty minutes, then an hour. If the temperature variance is considerable call a HVAC professional to take a look at your thermostat

6. Your thermostat has slack and/or corroded wires

Wires are configured to help the thermostat regulate heating and cooling functions of a thermostat. If one of the wires is lose then the temperature regulation will also be affected

Your thermostat has broken components or the whole thermostat is busted

You may need a thermostat repair or replacement and it is free under warranty

When installed by a professional contractor, the Braeburn Builder 500 and 505 mechanical models have a one- year limited warranty

7. Your air filters are blocked

A dirt-free air filter in a Braeburn thermometer helps to improve air quality and keeps a steady temperature. Experts recommend switching your air filter every three months.

Remove the air filter from your furnace and give it a good inspection.

Fix: Your air filter needs to be changed if it has darkened, is greasy and/or filthy.

Fix Also, if your filter is no longer transparent, then it will necessitate replacement.

The Braeburn 6425 touchscreen model has three user selectable service displays that will show reminders for an essential air filter, UV bulb or humidifier pad replacement.

The SERVICE segment flickers in the display along with FILTER, UV or HUMID.

When the service period has been arrived at, and obligatory cleaning or replacement has been executed, touch the RETURN TouchPad to reset the timer.

8. Your Braeburn thermostat placement does not allow for optimum heating or cooling

Do not put your thermostat in a room that heats or cools more than the rest of your home.

When setting up the non-Programmable the Braeburn 1020 and 1220 Braeburn thermostats avoid locations with drafts, dead air spots, hot or cold air ducts, sunlight, appliances, concealed pipes, chimneys and outside walls.

Fix – Move your thermostat away from fireplaces, windows, or kitchens.

9. Your Braeburn thermostat may not be flush with the wall

If your thermostat is floppy or dangling off the wall, then you need to balance it out so the pin connection between the thermostat and backplate can give a correct reading temperature reading.

A HVAC professional can help you reposition your thermostat and understand the best likely placement for optimum temperature readings.

10. Your Braeburn thermostat screen is blank

Your thermostat display is empty due to lost power. Your condenser and furnace may have also ceased working.

Braeburn thermostat may have blown a fuse leading to the display screen showing a blank screen. Look at the circuit breaker for any tripped breakers.

Acquaint yourself with your particular Braeburn thermostat model manual for added troubleshooting if it is not turning on.

Fix – Call a HVAC expert to conduct repairs on your thermostat and electrician due to power outage.

11. Your Braeburn thermometer is now too dated

The average lifecycle of a thermostat is around ten years. An old thermostat will have a more difficult time trying attain set temperatures and a key deterioration in its accuracy.

Fix – Plan how to replace your system and give your HVAC experts a call.

Do the temperatures emanating from your Braeburn thermostat fluctuate as you move from room to room?

Have you experienced a problem where at least one room in your house is either too hot or too cold? Your living room could be at the precise toasty temperature you desire, but your bedroom upstairs or kitchen next door is glacial.

Common causes of temperature imbalances in your residence are:

12. Imperfectly sized ductwork or thermostat

Wrongly sized ductwork or thermostat prevents you from realizing the airflow you need thus impacting the heating and cooling constancy in your home.

It can also lead to long term damage to your system. In winter, incorrect airflow can cause your system’s evaporator coils to freeze up. In summer, your system can overheat and fail early.

Fix – Use duct tape

Fix 2 – Contact a HVAC professional to know which is the right duct and thermostat size for your home

Fix 3 – Add a second thermostat system to remedy improperly sized HVAC or ductwork

View on Amazon

It will let you have better regulation over different floors. Have your system scrutinized by a professional before you decide on this

11. Permeable ductwork

Leaky ducts can drop with about 30% of airflow.

Even slight leaks from badly insulated ducts can influence airflow all over the house. Large leaks, including those from loose joints and fittings, can totally remove airflow to distant rooms.

Fix: Have repairs done ductwork on any leaks and also check for loose joints and improper insulation

12. Inadequate Insulation

Older homes tend to have mediocre insulation and paper-thin walls that cannot maintain heat or cool air.

Even though the fluctuating temperatures affect specific rooms, you will end up operating your thermostat for a more extended period than necessary.

This leads to energy wastage and overspending to acclimatize the entire house.

Fix: The US Department of Energy has great advice on better insulation for your residence. Call a HVAC professional for further assistance.

13. Rising heat in multi-level homes

Usually, upstairs houses have an eight to ten degrees temperature difference between the upstairs and the downstairs because heat naturally flows from lower to higher levels, leaving the upstairs rooms warmer.

Also, most heating and cooling systems only examine the temperature around a single thermostat, which can leave rooms at the extreme ends or overhead under-conditioned.

14. Thermostats are most successful in the room they are installed

Thermostat are best at controlling temperature in the room that they are installed in.

If thermostat is put in your living room you will find that when that room hits the pre-set temperature, the whole system will shut down to prevent the house from overheating.

This transpires whether or not the rest of rooms have attained the same temperature.

15. Rooms are far away from your thermometer

The rooms closest your furnace or cooling unit will naturally receive the bulk of the conditioned air.

Those that are further away or at the ends of the ductwork get far less airflow leading to uneven heating or cooling in contrast to the rest of the room.

16. The location of rooms and windows affect temperature stability

Are your rooms located in a sunny or cold facing side of the house?

Are your windows too small, too big, too many, or not enough?

How is the sealing on your windows? All these questions affect the overall temperature.

A lot of heat could be going out through the window even when its closed.

If your bedroom is relatively small and window is right over the head of the bed you could also lose a lot of heat or coolness.

Fix – Add a zoning system

Room zoning systems let you to regulate the temperature independently from thermostats installed on each different floor.

These thermostats are assembled to control panels all over your home and interconnect with dampers that are fitted in your ductwork.

Some rooms have air dampers or louvres that can be adjusted to direct more heat to one room than another.

These dampers are directed to open and close automatically based on how you set the individual thermostats.

Zoned systems also permit you to heat or cool separate rooms on demand, or close off vacant rooms entirely.

Fix 2 – Install Smart Vents system.

Smart vents are connected to the internet allow you to manage vent registers in specific rooms, similar to the dampers in traditional zoning systems.

Finally get an energy audit done in your home to determine the source of your imbalance and to find the right solution.

Brady Klinger-Meyers is an experienced writer and marketer with who currently writes for Robodens as well as other popular sites like MakeUseOf and Techzillo. At Robodens, he focuses on general smart home advice with his interest being accessories and gadgets. Read our Editorial Guidelines and Fact Checking process.

LEAVE A REPLY

Please enter your comment!
Please enter your name here